Electrode Equipment Makers: 23 Firms by Process

Battery electrode equipment is the R2R (Roll-to-Roll) family that coats and dries slurry on a current collector (coater), presses it to target density (calender) and cuts it to width and shape (slitter, notcher). The basis for comparing makers is not process coverage but the mechanical structure that holds thickness and width tolerances. This article groups 23 electrode equipment makers verified from public sources by process, and checks by calculation how much calender roll deflection eats into the thickness tolerance.

Problem Definition

Wet coating followed by roll-press calendering is the mainstream electrode process. Makers compete on width and speed. PNT discloses high-speed wide lines of 1,400 mm width at 100 m/min or more, and Haoneng an 1,800 mm ultra-wide two-layer extrusion coater. At the same time, CIS states a guaranteed pressed thickness of ±1.5 µm (company public materials).

Width is the contradiction. A wider line means a longer bearing span and a larger roll deflection. When the gap opens at the center more than at the edges, the electrode gets thicker in the middle. So what should be asked first when comparing wide lines? Our answer: the roll deflection calculation at design load and the crown and bending compensation method.

Kinematic Analysis — Mechanical Issues by Process

ProcessGoverning mechanical variableTypical riskMakers
Coating and dryingSlot-die lip gap, backup roll runout, web tensionCross-web coat weight variation; curling during dryingMannest, Sinyoo, Katop, Yakang, Haoneng, Coatema, Faustel, Time High-Tech
Calender (roll press)Roll bending and shear deflection, crown profile, roll thermal expansionCross-web thickness variation, wrinklesCIS, PNT, Matthews
Slitting and notchingKnife clearance and overlap, die wear, laser heat-affected zoneBurr, dust, web wanderKAMPF, Maxcess, Hymson, Phil Energy, Youil Energy Tech
InspectionSensor frame stiffness, scan speedLoss of measurement repeatabilityDacheng Precision
Dry electrodeSpeed differential between rolls, film-forming loadFilm breakage, poor bonding to the collectorAM Batteries, Matthews, Dürr

Full-line makers (NAURA, Leadyo, Han’s Lithium, Manz) take the interfaces between processes into their scope. There the comparison is not single-machine specification but how tension zones are split between coater, calender and slitter, and whether the transfer reference surfaces are unified.

Maker Comparison Table

The table lists only what is disclosed on official websites, in filings (DART, exchange annual reports) or in company press releases. Third-party revenue estimates were excluded. Makers with a detailed profile are linked.

MakerHQMain processDisclosed factsBasis
CIS (SFA Nexel)Daegu, KoreaCoater, calender, slitterKOSDAQ 222080. Localized the calender in 2008; guarantees ±1.5 µm pressed thickness and slitter burr within 10 µm. 2024 revenue KRW 132.7 billion (roll press 67%)Company materials, industry press
PNT (People & Technology)Gumi, KoreaCoater, calender, slitter, notcherKOSDAQ 137400. High-speed wide lines for 6 µm foil, 1,400 mm width, 100 m/min or more. 2025 revenue down 28.0% year on yearDART filings
Phil EnergyGyeonggi, Korea (near Osan)Stacking, laser notchingKOSDAQ 378340, listed on its own in 2023. Disclosed a KRW 71.19 billion assembly equipment contract in 2026-07DART filings
Youil Energy TechAnseong, KoreaNotching, stackingKOSDAQ 340930. Founded 2012; notching, stacking and tab welding equipmentDART filings, press
MannestShenzhen, ChinaCoating die headsChiNext 301325. No. 1 coating die head maker in China (company statement). 2025 revenue CNY 1.068 billion, net loss CNY 110 million2025 annual report
SinyooGuangdong, ChinaCoater (SDC simultaneous double-side coating)Up to 70 m/min at 1,200 mm coating width, coat weight variation within ±1.0% (company figures)Company website, OFweek
Katop (Jiatuo Intelligent)Changzhou, ChinaElectrode and separator coatersAutomation arm of Putailai Group. Double-side high-speed coaters, gravure primer coatersCompany website
Yakang PrecisionDongguan, ChinaCoater, roll press, slitter, winderOwn brand ARECONN. Site 23,500 m², about 900 employeesCompany profile materials
Haoneng TechnologyShenzhen, ChinaCoater, roll pressSubsidiary of Keheng (under Gree group). 1,800 mm ultra-wide two-layer extrusion coaterShanghai Securities News, Sina Finance
Shenzhen Time High-TechShenzhen, ChinaElectrode and cell vacuum dryingVacuum drying systems to replace hot-air ovens; tab welding equipmentCompany website
Dacheng PrecisionDongguan, ChinaCoat weight and thickness gauging, vacuum dryingX-ray/β-ray coat weight gauges, combined CDM thickness and coat weight gauges. Claims over 60% of China’s electrode gauging market (company claim)instrument.com.cn
HymsonShenzhen, ChinaLaser notching and cuttingSTAR 688559. Entered with laser tab cutting in 2015. Laser scribing at 80 m/min, over 50 units deliveredCompany website, annual report
LeadyoHuizhou, ChinaFull lines from electrode to assemblySTAR 688499. Built a full solid-state line; won a US module line order in 2024-10Company disclosures
NAURABeijing, ChinaLithium battery equipment from mixer to winder (side business)Shenzhen 002371, China’s largest semiconductor equipment maker. 2023 group revenue CNY 22.08 billion (battery division not disclosed)Public financials
Han’s LithiumShenzhen, ChinaRoll press, die cutting, slitting to formation turnkeyFounded 2018, Han’s Laser (002008) group companyPublic industry materials
DürrGermanyWet and dry electrode linesGained dry coating (X.Cellify DC) through the LiCAP acquisitionelectrive, Charged EVs
Manz AGReutlingen, GermanyElectrode and assembly equipmentInsolvency proceedings opened 2025-02; sites sold separatelyCompany insolvency notice
KAMPFWiehl, GermanySlitters, windersFounded 1920, Jagenberg subsidiary. TechSlitter rewind diameter up to 800 mm, used by Gränges for cathode foilCompany website
CoatemaDormagen, GermanyR&D and pilot coaters and calendersATH Group. Calender working width 100 to 2,000 mm, line force 6 t (pneumatic) to 80 t (hydraulic)Company website
FaustelGermantown, USAModular coating linesFounded 1956. LabMaster 300 and 600 mm pilot lines; joint turnkey lines with JagenbergCompany website
Matthews InternationalPittsburgh, USAMulti-roll calender for dry electrodesNasdaq MATW. Patented system combining calendering and double-side lamination; four calender lines supplied to Evonik LitarionCompany materials
MaxcessOak Brook, USAWeb guiding and slitting componentsFife guiding, Tidland knife holders and air shafts, MAGPOWR tension controlCompany website
AM BatteriesMassachusetts, USADry powder deposition (Powder to Electrode)Founded 2016. Claims 30 to 40% lower capex and 45 to 75% lower energy than wet coating (company figures). First NMC cathode rolls shipped in 2023Company announcement

Coating — the lip gap behind the width and speed race

Coater makers quote width, speed and coat weight variation together. Sinyoo says its SDC method dries both sides at once in a single oven and reduces the curling of shuttle-type two-pass coating. Mannest supplies die heads as separate units. When the die head is bought separately, responsibility for lip gap and backup roll runout is split from the coater body maker, and root-cause isolation of coat weight variation becomes difficult. Tie the die mounting face flatness and backup roll runout allowance into the same contract specification.

Calender — thickness tolerance is the localization benchmark

CIS localized the calender in 2008, and roll presses made up 67% of its 2024 revenue. PNT develops coaters, calenders, slitters and notchers in house. Both are known to have supplied Korea’s three major cell makers. As the calculation below shows, the key point in comparing calenders is the roll deflection compensation method.

Slitting and notching — burr and dust

KAMPF supplies TechSlitter for battery cathode foil, and Maxcess supplies guiding, knife holder and tension control components. Hymson entered with laser notching in 2015 and expanded to electrode-to-assembly lines. Mechanical knives reduce burr through clearance control; lasers avoid die wear but must manage the heat-affected zone and fumes.

Dry electrode — the calender replaces the coater

AM Batteries deposits powder directly on the current collector without solvent. Matthews supplies a multi-roll calender that combines calendering and double-side lamination in one step. In the dry process the drying oven disappears, but the calender takes the entire film-forming load, so calender roll stiffness requirements rise above those of wet lines.

Manz AG entered insolvency proceedings in February 2025 and its sites were sold separately. It shows that supplier financial condition decides spare parts and after-sales continuity.

Calculation and Formula Check — Calender Roll Deflection and Thickness Tolerance

The roll is simplified as a beam simply supported between bearings, with line load spread evenly over the full span. Deflection is the sum of bending and shear components. For a roll whose diameter is large compared with its span, the shear component cannot be ignored.

$$q = \frac{F}{L}, \qquad \delta_b = \frac{5 q L^{4}}{384 E I}, \qquad \delta_s = \frac{\alpha q L^{2}}{8 G A}$$

$q$ is line load (N/mm), $F$ is total press force (N), $L$ is bearing span (mm), $E$ is elastic modulus (N/mm²), $I=\pi D^{4}/64$ is second moment of area (mm⁴), $G$ is shear modulus (N/mm²), $A=\pi D^{2}/4$ is cross-section area (mm²), $\alpha$ is the shear coefficient of a solid circle (10/9) and $D$ is roll diameter (mm).

Example conditions: F=1,000 kN, L=1,400 mm, D=800 mm, E=206,000 N/mm², G=79,000 N/mm². F is an example value; re-confirm actual press force after on-site measurement.

ItemValueMeaning
Line load q714 N/mmPress force divided by span
Bending deflection δb8.6 µmCenter of one roll
Shear deflection δs4.9 µmAbout 57% of bending; not negligible
Total per roll13.5 µmUpper and lower rolls assumed equal
Center gap increase27.0 µmHow much the center opens versus the edges
Bending stress σb3.5 N/mm²$M=qL^{2}/8$, $Z=\pi D^{3}/32$

The safety factor is checked twice. SF1 is the strength criterion. Even with a conservative roll yield strength of 300 N/mm² (assumed; confirm with the material certificate), SF1 is 86. Strength does not govern. SF2 is defined on tolerance.

$$SF_2 = \frac{t_{tol}}{\Delta g}$$

$t_{tol}$ is the allowable thickness variation (µm) and $\Delta g$ is the gap variation remaining after compensation (µm). SF2 below 1 means the tolerance is exceeded. Without compensation, Δg=27.0 µm and SF2 is 0.06 against a ±1.5 µm tolerance. Even if a fixed crown cancels deflection at design load, a ±10% load change leaves Δg of ±2.7 µm, and SF2 is 0.56. A fixed crown is right at only one load. A ±1.5 µm thickness line is hard to hold without variable bending compensation.

Practical Application (Shop-notes)

  • When comparing quotations, ask for the roll deflection calculation at design force (bending plus shear), the crown profile and the variable bending range. A calculation that leaves out shear deflection underestimates deflection by 36% in this example.
  • Machinability: a crown is a micrometer-level profile, so it needs a CNC roll grinder and measurement after the roll temperature stabilizes. Grind the crown within the hardened case depth so regrinding allowance remains.
  • Alternative mechanism — roll crossing (crossed upper and lower roll axes): the crossing angle can compensate the center gap. Not adopted because axial thrust rises with the crossing angle, and thin current collectors are at higher risk of wander and wrinkles. Electrode calenders should consider roll bending cylinders first.
  • For slitters, put knife clearance and overlap control criteria and the burr measurement method (location and magnification) into the FAT items.

Design Checklist

  • Confirm that the roll deflection calculation includes both bending and shear
  • Confirm strength SF1 of 2 or more and tolerance SF2 of 1 or more (after compensation) at the same time
  • Compare the fixed crown design load with the actual operating load range
  • Confirm the variable bending range and response method
  • When buying die heads separately, state the responsibility boundary for mounting face flatness and backup roll runout
  • Confirm supplier financial condition and spare parts and after-sales continuity

One-line Summary

Electrode equipment should be compared on the roll gap variation left at design load, not on width and speed.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top